CALL US:
1-866-725-86093000 Series Aluminum is alloyed with Manganese and are high strength. 3000 Series Aluminum also exhibits moderate resistance to chemical agents, atmospheric agents and offers higher mechanical properties and better formability than pure aluminium. These alloys are not heat treatable.
Download Datasheet
3000 series Aluminum alloys are Aluminum alloyed with manganese. They have higher strength than pure aluminum while maintaining good formability and corrosion resistance. These alloys are not heat treatable and are suitable for anodizing and welding. Alloy 3003 is the most widely used of all the aluminum alloys.
UNS# A93003 | ALUMINUM | ADDITIONAL ELEMENTS
1.0-1.5 Mn, 0.05-0.20 Cu, 0.7 Fe max, 0.6 Si max, 0.10 Zn max, 0.05 max other (each), 0.15 max other (total)
UNS# A93004 | ALUMINUM | ADDITIONAL ELEMENTS
1.0-1.5 Mn, 1.0-1.3 Mg, 0.25 Cu, 0.70 Fe max, 0.30 Si max, 0.25 Zn max, 0.05 max other (each), 0.15 max other (total)
UNS# A93105 | ALUMINUM | ADDITIONAL ELEMENTS
0.20-0.80 Mn, 0.20-0.80 Mg, 0.30 Cu, 0.7 Fe max, 0.6 Si max, 0.40 Zn max, 0.20 Cr max, 0.10 Ti max, 0.05 max other (each), 0.15 max other (total)
*Contact Ulbrich Wire for request regarding the availability of other aluminum alloys.
Typical Density: 0.0983 - 0.0986 lbs/in3, 2.72 - 2.73 g/cm3
Electrical Conductivity: (% IACS at 68° F, annealed): 40-50%
Thermal Conductivity: BTU-in/hr-ft2-° F:
At 68 ° F: 1190 - 1340
Mean Coefficient of Thermal Expansion: µin/in-°F:
68 - 572 °F: 13.9
Modulus of Elasticity: KSI
10.4 x 103 in tension
Melting Temperature: 1165 - 1210 °F (629 - 654 °C)
Profile, Round, Flat, Square
Ultimate Tensile Strength: 16 KSI min (110 MPa min)
Yield Strength: 6 KSI min (41.4 MPa min)
Elongation: 24% min
These alloys can be cold worked to various tempers.
*Actual physical and mechanical properties are alloy dependent. Contact Ulbrich Technical Service for alloy specific properties.
Contact Ulbrich Wire for specific information.
XC - Extra clean. Annealed or annealed and cold rolled. Contact Ulbrich Wire with special finish requests.
These alloys are hardenable by cold working.
Contact Ulbrich Wire for specific information.
Limitation of Liability and Disclaimer of Warranty: In no event will Ulbrich Stainless Steels & Special Metals, Inc., be liable for any damages arising from the use of the information included in this document or that it is suitable for the 'applications' noted. We believe the information and data provided to be accurate to the oest of our knowledge but, all data is considered typical values only. It is intended for reference and general information and not recommended for specification, design or engineering purposes. Ulbrich assumes no implied or express warranty in regard to the creation or accuracy of the data provided in this document.
Thanks for your interest in Ulbrich! Whether you're developing a new product or ramping up production, we'll be happy to learn more about your specific needs. Please fill out the form below, and we will promptly get back to you with a quote or, if needed, a request for more information.